How Do We Know That Corrugated Metal Pipe is Reliable?

Corrugated metal pipe has been used in drainage applications in the United States since the late &#;s.

YiTong Product Page

For most of the 20th century, the two most frequently installed stormdrain pipe materials were concrete pipe and galvanized corrugated steel pipe.

For instance, there are ~65,000 stormdrain pipes in Gwinnett County&#;s GIS database with installation dates between and . About 17,000 of the pipes are concrete pipe (~27%) and about 45,000 of the pipes are galvanized or asphalt coated galvanized pipe (~70%).

How have these materials performed over time?

The Problem with Galvanized Corrugated Steel Pipe in Georgia

Every stormdrain pipe material has recommended applications and environmental condition restrictions.

Corrugated metal pipe is recommended for the following environmental conditions according to the Georgia Department of Transportation:

Out of all these corrugated metal pipe products, galvanized steel pipe (zinc coated) is the most sensitive to environmental conditions.

Compare the allowable pH range for galvanized steel pipe (minimum 6.0) vs aluminized type 2 steel pipe (minimum 4.50).

The pH system is a logarithmic scale, so a 1.5 lower pH value translates to an environment that is ~30 times more acidic.

Environmental Conditions in the Atlanta Area

The USDA Natural Resources Conservation Service provides soil survey information online, which allows you to select an area of interest and download the expected soil and water characteristics based on the recorded soil surveys.

Let&#;s look at the soil conditions in the Atlanta area, using Gwinnett County as an example again.

If you select Gwinnett County as an area of interest and pull up the &#;Soil Chemical Properties&#;, then you can select pH values and download a table of the expected soil types and pH values. You can download the information as a PDF report (USDA Expected Soil pH Values &#; Gwinnett County).

We have summarized the USDA information below.

If you compare the USDA information to the recommended environmental conditions for galvanized steel pipe, then you can see why the material is underperforming in the Atlanta area.

Galvanized CMP should be installed in environments with a pH of 6.0 or higher, but just 1.5% of Gwinnett County falls within that range.

Aluminized CMP is recommended for environments with a pH of 4.5 or higher, so none of the USDA&#;s expected environmental conditions fall outside of the recommended range for aluminized steel pipe.

Why Does Aluminized Type 2 CMP Perform Better in More Aggressive Environments Compared to Galvanized?

Aluminum and aluminum alloys are very stable when they are exposed to an environment with pH values between 4.0 and 9.0. Included below is a chart from Uhlig&#;s Corrosion Handbook.

Field measurements of pH may vary, so the industry leaves some safety cushion in the recommended environmental conditions for AT2 CMP, so the recommended lower pH limit is 4.5 instead of 4.0.

How Do We Know That Aluminized CMP will Outperform Galvanized CMP in Georgia?

Let&#;s start with some visual comparisons of aluminized CMP and galvanized CMP installed at the same time and in the same environments.

The image below is a pipe that was manufactured partially from galvanized steel and partially from aluminized type 2 steel. The pipe was left in service for 30 years and then examined.

The visual difference between the two materials is dramatic.

One of the easiest places to compare the performance of galvanized and aluminized CMP is at a headwall connection. Most precast headwalls are manufactured with a galvanized CMP stubout, so when an aluminized type 2 CMP pipe is connected to the headwall then you can see a direct comparison of the products.

This pipe is located in Barrow County, Georgia. It was 17 years old at the time the picture was taken. The galvanized stubout is beginning to fail at the invert but the aluminized pipeline is performing well.

The red coloration you can see in the pipe invert was easily removed with a brush and the pipe surface still has a silver sheen because of the intact aluminum coating.

The aluminized pipe was measured as part of the NCSPA&#;s Atlanta area study of AT2 CMP. This pipe still had more than 90% of its aluminum coating remaining when this picture was taken.

The next visual is a video that was published by Contech Engineered Solutions. They examined a 30-year old installation where a 78&#; diameter aluminized CMP culvert is outperforming the galvanized end section that is connected to it.

What Information is Available on the Real-World Performance of Aluminized Type 2 CMP?

Aluminized type 2 corrugated steel pipe has been around since the early &#;s. The product has been thoroughly studied for decades.

NCHRP Report 801 &#;Proposed Practice for Alternative Bidding of Highway Drainage Systems&#; states that:

&#;Currently, there are more well defined methods to estimate the service life of steel culverts than any other type of material&#; (page 57).

Information Source 1: Minnesota DOT

Minnesota DOT published a report in titled &#;Improving the Selection and Testing of Culvert Pipe Materials&#;. They recommend using aluminized type 2 CMP because its service life is 3 to 8 times better than galvanized CMP.

A research team at the University of Minnesota presented to MDOT in . The presentation was called &#;Culvert Pipe Materials and Durability: Making the Right Selection for Minnesota&#;.

The research team examined the DOT&#;s culvert inspection database to see how various pipe materials are performing. They recommended replacing galvanized CMP with aluminized CMP because of the better service life. Interestingly, they also state that 18% of the RCP in Minnesota DOT&#;s database has joint separation issues.

Information Source 2: Gwinnett County&#;s GIS Database

Gwinnett County has been assessing the condition of their existing stormdrain pipe infrastructure since . Each pipeline was inspected and assigned a condition rating of &#;Good&#;, &#;Fair&#;, or &#;Poor&#;. This condition data was updated in their publicly available GIS database until .

The database includes more than 145,000 pipelines and lists the pipe material, location, estimated date of installation, and pipe condition. The information in the database is summarized in the tables below.

The condition data was gathered internally by Gwinnett County for their own maintenance planning purposes, but the summary tables below were compiled by Southeast Culvert.

Material type acronyms:

• RCP (reinforced concrete pipe)
• BCCMP (asphalt coated galvanized corrugated steel pipe)
• AT2 CSP (aluminized type 2 corrugated steel pipe)
• HDPE (high density polyethylene pipe)
• GALV (galvanized corrugated steel pipe)

When the data is broken down by pipe material type, you can clearly see the performance differences among various material options.

1. The worst performing pipe material in the database is galvanized CMP.
2. Bituminous coated galvanized CMP is performing significantly better than galvanized.
3. RCP is middle of the pack. It&#;s doing better than galvanized and BCCMP, but worse than HDPE and aluminized type 2 CMP.
4. HDPE pipe is the second best performing material in the database.
5. Aluminized type 2 CMP is the top-rated material by a significant margin.

The install dates for the database go back to , so let&#;s look at the statistics for the oldest installations.

Narrowing the time frame to the period between and reduces the number of pipelines to ~65,000. The performance differences between the various material types also becomes more pronounced.

Galvanized CMP is clearly performing worst with ~9% of the galvanized pipes in &#;poor condition&#;.

RCP, BCCMP, and HDPE are all in the same ballpark, around 3% in &#;poor condition.&#; HDPE is performing the best in that group.

Aluminized type 2 has the most pipes in &#;good condition&#; by a large margin (27% vs < 10% for the rest of the materials). It also has the least proportion of pipes in &#;poor condition&#; (~1%).

Information Source 3: Cobb County&#;s GIS Database

Cobb County has a GIS database that is comparable to Gwinnett County. The number of inspected facilities was smaller as of , but the statistics are similar.

The condition data was gathered by Cobb County for their own maintenance purposes, but the summary tables below were compiled by Southeast Culvert.

Their database includes ~ 78,000 pipes categorized by pipe material, location, estimated date of installation, and a pipe condition assessment. They assessed each pipeline and assigned the pipe a condition of &#;Good&#;, &#;Poor&#;, and &#;Failing.&#;

Material Type Acronyms:

• RCP (reinforced concrete pipe)
• BCCMP (asphalt coated galvanized corrugated steel pipe)
• AT2 CSP (aluminized type 2 corrugated steel pipe)
• HDPE (high density polyethylene pipe)
• Uncategorized CMP

Cobb&#;s statistics show a similar pattern as Gwinnett County.

1. Aluminized Type 2 CMP has the smallest proportion of pipes in failed condition and the largest proportion in good condition.
2. HDPE is the second best performing product.
3. BCCMP / Uncatagorized CMP tie for second worse performing product with ~ 1 percent in failed condition.
4. RCP is the worst performing product in Cobb&#;s statistics by a large margin.

Let&#;s look at some of the older pipe in Cobb&#;s database. When the data is filtered for install dates between and , the number of pipelines drops to ~55,000.

The older pipes show a similar pattern. Aluminized CMP is the best performing product. BCCMP, Uncategorized CMP, and HDPE are middle of the pack, and RCP is the worst performing pipe material.

Information Source 4: Georgia DOT and Oregon DOT

Within the recommended environmental conditions, the expected service life of aluminized type 2 CMP is 75 years minimum for 16 gauge pipe and 100 years minimum for 14 gauge pipe.

If you are looking for more details, kindly visit Galvanized Culvert.

Galvanized CMP has an average service life of 40 years in the recommended environmental conditions (which are not commonly found in Georgia).

Because of the performance differences between the products, most DOTs in areas with lower pH environments use aluminized CMP instead of galvanized.

The Georgia Department of Transportation updated their stormdrain standards in and revised their stormdrain pipe selection chart.

They upgraded the use of AT2 CMP to be allowed underneath roads with an expected traffic of 5,000 cars per day. GDOT uses a 75-year min service life guideline for pipe materials underneath a road.

Notice that galvanized (zinc coated) CMP is not allowed inside the roadbed on GDOT projects.

The Oregon Department of Transportation explicitly lists the service life expectations for their stormdrain products in the ODOT hydraulics manual.

Galvanized CMP is listed with a service life between 15 and 40 years depending on the environment.

Aluminized CMP, RCP, and plastic pipe are all listed with a 75-year service life.

Information Source 5: &#;Durability of Aluminized Type 2 Corrugated Steel Pipe Exposed Throughout the United States&#; &#; Report by Elzly Technology Corporation

Aluminized type 2 has been studied on an ongoing basis since the early &#;s. More than 125 AT2 CMP pipes were installed in coordination with 20 state and county DOT&#;s and revisited every 10 to 15 years for an updated performance report.

The most recent durability study was published by Elzly Technology Corporation in and included pipes that have been in service for 60 years.

The conclusions of the study support the 75-year minimum service life for 16 gauge Aluminized Type 2 CMP in culvert applications.

Culvert applications are significantly more aggressive than storm sewer applications because of bedload conditions. Storm sewer applications are considered to have little or no bedload according the FHWA guidelines.

In stormdrain applications, the 75-year minimum service life guideline for AT2 CMP is very conservative, which is why the next study&#;s results are so dramatic.

Information Source 6: &#;The Measured Performance of Aluminized Type 2 Steel Pipe in Storm Sewer Applications in the North Georgia Region&#; &#; Report by the National Corrugated Steel Pipe Association

In the NCSPA began building a database of aluminized type 2 CMP installations in the Atlanta area. In total, 140 pipes were inspected and measured for aluminum coating loss and the results were charted against the expected wear rates for the material to provide a 75-year service life.

The study locations were widely scattered across north Atlanta. Most of the pipes have been in service for more than 20 years at the time of inspection.

The results of the study show that AT2 CMP installed in stormdrain applications will provide a service life far in excess of 75 years.

The average wear rate of the aluminum coating was 0.84% loss per year. At that rate, there will be substantial aluminum coating on these pipes after 100 years of service.

The average coating wear rate for the pipes that have been installed for more than 30 years was 0.78% loss per year, which shows that the aluminum coating provides consistent protection even after decades of service.

You can find the full report on the NCSPA&#;s Studies and Reports webpage.

Conclusion

For most people, the distinction between the many types of corrugated metal pipe is blurry. Contractors, engineers, and municipal reviewers often have an opinion on the product as a general category.

A reviewer might say &#;we allow metal pipe&#; or &#;we don&#;t allow metal pipe&#; for a project, but the specific type of CMP material makes a big difference on the expected service life of the pipe.

In Georgia conditions, galvanized CMP does not perform very well. The soil and water pH values are generally outside of what is recommended for the product. In other regions of the country with different environmental conditions, the product performs very well and can exceed the 40-year service life expectation

Aluminized type 2 CMP has proven to perform very well in Georgia conditions, which is why it is allowed underneath major roads on Georgia DOT projects and in many Atlanta area municipalities.

If you are specifying a CMP product on a project in Georgia, then mostly likely you should use aluminized CMP.

Let us know if you have a question about whether the pipe is appropriate for a specific application on a project, or if you have any questions about CMP or HDPE products.

Culverts are not your regular pipes. If you&#;re not sure what type of culverts you need or you&#;d like to know more about them and their intricacies, you&#;re in the right place. This article will explain what culverts are, dissect their different shapes and sizes, and help you find high-quality culvert pipes in Rochester.

What are culverts?

Culverts are tunnel-like structures that can carry water and wastewater. They can be found under roads, railways, and soil. Their purpose is to limit and direct the waterflow to relieve drainage, prevent floods, and allow crossings over the waterway.

Sometimes, their purpose coincides with that of a bridge, but there are many differences. As they are different structures, they require a different and proper inspection to ensure they&#;re functional, performing well, and structurally adequate.

What material are culverts made of?

What material are culverts made of?

One of the most important aspects of culverts is the material used for its construction. Here are a few options:

Steel

There are usually two main types:

• Structural steel plate (SPP): This material is very durable and provides excellent corrosion resistance. It&#;s used to construct metal box and arch culverts.

• Corrugated steel pipe (CSP): Pipe culverts are typically constructed from this material as it makes the pipe strong and flexible, which is important due to its round shape.

Concrete

Concrete is another common material used for culvert construction. It is strong and long-lasting. It also has a low environmental impact on its surroundings. Box culverts made of concrete are common in both urban and rural areas. 

Aluminum

Typically made from structured plates, aluminum culverts are usually metal box culverts. Aside from being light, they provide excellent corrosion resistance and are recyclable.

High-density polyethylene (HDPE)

HDPE culverts are usually pipe culverts. This material makes them light, yet strong. They&#;re also weather-resistant, and impact-resistant. HDPE is not only long-lasting, but also easily molded into different shapes, so it&#;s a good choice for culvert construction.

What are the standard sizes for culverts?

The size of a culvert depends on many factors, such as the specific project, area, state regulations, etc. Usually, culverts come in 10, 12, and 20 feet lengths or they&#;re custom-made to fit the client&#;s requirements.

When it comes to the diameter, it can range from 6&#;&#; to 96&#;&#; and more. Again, as it should be safe, durable, and effective, a culvert should be constructed to fit the unique circumstances and requirements of each individual client.

What are the different shapes of culverts?

To fit the needed waterflow capacity, environment, and other conditions, culverts come in different shapes. They can be round, pear-shaped, elliptical, box-like, and flat-bottomed.

Their unique features make for different culvert types, such as the following:

• Pipe culvert

• Arch culvert

• Bridge culvert

• Pipe-arch culvert

• Box culvert

• Metal box culvert

Where can you get high-quality culvert pipes in Rochester & the nearby area?

When you need reliable and durable water and wastewater material and equipment, look no further than Blair Supply Corp. We have been a trusted supplier of culverts for over 60 years.

We follow the latest industry trends, work with dependable suppliers, and boast a team of qualified and experienced experts in their field.

Our company strives to innovate and keep improving our business to cater to different clients in Rochester and Watertown in the best possible way.

Give us a call, and we&#;ll be happy to answer all your questions about culverts and other equipment. Blair Supply Corp. is at your disposal from that initial call to the execution of your requested project. Reach out to us today and see for yourself why we&#;re the leading culvert distributor!

If you want to learn more, please visit our website Culvert Piping Plastic.